$208.00 $156.00

Steering Rack Brace & Clamp Kit
[SRBK]

Steering Rack Brace & Clamp Kit

Add to Cart

Date Added: Thursday 07 April, 2011

by Steve Beisser

I bought a 2000 9-3 conv. 5 speed back in Sept. I love the car, but did not like some of the handling characteristics (major torque steer-which is really a problem when driving a 5 speed since only one hand is on the wheel when accelerating hard and winding through the gears, excessive body lean through turns, and cowel shake). I decided to buy this steering rack brace kit along with the rear sway bar. I ordered it on Monday and they arrived on Thursday. I just put in the steering rack brace and took it for a spin. All I can say is THANK YOU TALIAFERRO! The torque steer is GONE!. I do notice a slight more amount of road feel coming through the steering wheel, but i actually like this. Truth is, it is very minor and I only noticed it because I just installed the thing and was really trying to see what the differences were. The installation was not difficult (I was surprised that no instructions were provided but found the installation photos on this site). It took me about an hour to install. Some helpful hints. The upper strut brace gets in the way, so if you are planning on replacing that too it would make this job easier to remove the factory one, then install this rack brace, then install the new strut brace. I also found working on the lower bolt to be a bit of a challenge since you can't see it. One last thing to note. You do not have to remove the front right wheel as I have seen suggested in order to get at the nut on the bolt that goes through the wheel well, I just turned the wheel all the way to the left, which allowed me to put my 10 mm box wrench on the nut inside the wheel well and then reached over the fender to tighten the bolt with a 10 mm socket. Getting my torque wrench on the bolts was a challenge (upper strut brace gets in the way) but hopefully I got the torques OK. I will re-check after 100 miles as they suggest. Next on the list is the rear sway bar, then I plan on installing the upper strut brace and the 6 point sub frame brace. I plan on doing each upgrade one at a time and will report back the results. As far as this one goes - it's a no brainer. Everyone with this car needs to install this. In my opinion, it should be viewed as a safety feature (of course, it also increases the fun factor too!) It's hard to believe Saab let this model out of the factory without this.

Rating: 5 of 5 Stars! [5 of 5 Stars!]

Write Review Back
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
2 x Rivetnuts Pair (2pcs)
2 x Rear Camber Shims Kit 6pcs
2 x Short Shifter NG900/9-3 94-02/9-5 (Outright Kit)
3 x Viggen Titanium KeyChain
1 x Rear spring perches Adjustable NG900/9-3
1 x PPC - Upgrade from stage 1 to stage 3
1 x Map/MAT sensor weld bung
2 x 9-3 / 900 Uprated Suspension Bushings Inner
1 x Rear Engine Mount 4cyl
1 x 9-3 99-02,03 CV Antenna Adaptor
1 x 9-3 ng900 Hood Protection Strip
1 x 9-3 /NG900 Grille
1 x ARP Exhaust Manifold Stud kit Stainless
1 x Fog light 9-3 Right 99-00
1 x Downpipe Flange Assy. Stainless T25/Td04 to 3in
1 x Short Shifter HHR Cobalt F35 F40
1 x Forge Bypass Valve Cobalt/HHR TC
1 x K&N Filter Service Kit
1 x Fog light 9-3 left 99-00
1 x 5d Rear Window repair kit 94-02 900/9-3/9-5
1 x Aluminum Flywheel For NG900/9-3
1 x Catback 2.5in Exh 9-3 99-02 Wide Oval Tip (NOT VIG)
1 x Exhaust manifold Stud Kit
1 x Coreganizer
1 x Exhaust Clamp Kit
1 x MTF0063 Manual Gear oil
2 x 9-3 ng900 radio wires
1 x Saab black Keychain
1 x Floormats BSR 9-3 99-02 900 94-98
1 x Replacement Flywheel Insert NG900/9-3
1 x Shifter Mount Kit Cobalt/ HHR
1 x Flex Pipe 900 94-98 9-3 99-02
1 x Antenna Plug NG900/9-3 hatchback
1 x ARP Ring Gear Bolts F25/F35
1 x 9-3/NG900 Shift Knobs Leather
1 x Cat back for Viggen 2.5in
1 x Header Flange 1/2in Blended Transition B2x4,B2x5
1 x Fuel Pressure Regulator 4.0 bar
1 x Adaptor Harness Handsfree 01-
1 x Injectors Siemens 60lb 630cc (set 4)
1 x 3pt Subframe Brace for 9-3 SS 2003-> 2wd
2 x Sport Transmission Mount 9-3/900 (Automatic)
1 x Viggen Clutch Kit 99-02
2 x Griffin logo Shifter Top
2 x Flywheel Twin Disk 7.25in B2xx
1 x Quaife Differential 9-5 and Viggen (F35)
1 x Shifter Top Ghost Logo
1 x PPC 3 Volvo Diagnostic System
1 x Injectors Green Giant 42lb (set 4)
1 x Catback 2.5in Exh 900/9-3 94-02 Round Tip
1 x IAT Weld Bung T5/Bosch
1 x Basic Subframe Brace
1 x Slave Cyl
1 x Injectors Siemens 80lb 875cc (set 4)
1 x Front Camber Adjustment Bolts
1 x BSR Optiflow Intake 4cyl
$10,709.86
Manufacturer Info
Taliaferro
Other products
Share Product
Share via E-Mail