$208.00 $156.00

Steering Rack Brace & Clamp Kit
[SRBK]

Steering Rack Brace & Clamp Kit

Add to Cart

Date Added: Thursday 07 April, 2011

by Steve Beisser

I bought a 2000 9-3 conv. 5 speed back in Sept. I love the car, but did not like some of the handling characteristics (major torque steer-which is really a problem when driving a 5 speed since only one hand is on the wheel when accelerating hard and winding through the gears, excessive body lean through turns, and cowel shake). I decided to buy this steering rack brace kit along with the rear sway bar. I ordered it on Monday and they arrived on Thursday. I just put in the steering rack brace and took it for a spin. All I can say is THANK YOU TALIAFERRO! The torque steer is GONE!. I do notice a slight more amount of road feel coming through the steering wheel, but i actually like this. Truth is, it is very minor and I only noticed it because I just installed the thing and was really trying to see what the differences were. The installation was not difficult (I was surprised that no instructions were provided but found the installation photos on this site). It took me about an hour to install. Some helpful hints. The upper strut brace gets in the way, so if you are planning on replacing that too it would make this job easier to remove the factory one, then install this rack brace, then install the new strut brace. I also found working on the lower bolt to be a bit of a challenge since you can't see it. One last thing to note. You do not have to remove the front right wheel as I have seen suggested in order to get at the nut on the bolt that goes through the wheel well, I just turned the wheel all the way to the left, which allowed me to put my 10 mm box wrench on the nut inside the wheel well and then reached over the fender to tighten the bolt with a 10 mm socket. Getting my torque wrench on the bolts was a challenge (upper strut brace gets in the way) but hopefully I got the torques OK. I will re-check after 100 miles as they suggest. Next on the list is the rear sway bar, then I plan on installing the upper strut brace and the 6 point sub frame brace. I plan on doing each upgrade one at a time and will report back the results. As far as this one goes - it's a no brainer. Everyone with this car needs to install this. In my opinion, it should be viewed as a safety feature (of course, it also increases the fun factor too!) It's hard to believe Saab let this model out of the factory without this.

Rating: 5 of 5 Stars! [5 of 5 Stars!]

Write Review Back
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x 9000 Shifter Bushing Repair Kit
1 x Con Rods V6 2.8L 155.8mm
1 x SCNA Christmas Calendar
2 x Limit Strap Coilover Add On Kit
1 x B207 Coolant Cap
1 x Moog Ball Joint
1 x Replacement V6 Coolant Cap
1 x 3 Point Hardware
1 x Rear Camber Shims Kit 6pcs
1 x Steering Rod Bushings NG900/93
1 x Machined Control Arm Kit
1 x Steering Coupler 9-3 99-02
1 x Basic Subframe Brace
1 x Rear spring perches Adjustable NG900/9-3
1 x Turbo Conversion Pipe 900 9-3 T5
1 x T7 Injector Spacer Kit
1 x Oil Cooler Adaptor B2X5
1 x Catback 2.5in Exh 900/9-3 94-02 Round Tip
1 x T7 3.5 Bar Fuel Pressure Regulator
1 x Viggen Fog Air Intake
1 x Throttle Bend for T5 94-99
1 x Open Air Intake 9-3 00-02 and Viggen (All T7)
1 x Shift Rod Bushings
1 x Replacement Flywheel Insert NG900/9-3
1 x Shifter Top Ghost Logo
1 x Sport Transmission Mount 9-3/900 (Automatic)
1 x Slave Cyl
1 x Rear Engine Mount 4cyl
1 x Short Shifter NG900/9-3 94-02/9-5 (Outright Kit)
1 x ARP Ring Gear Bolts F25/F35
1 x Quaife Differential 9-5 and Viggen (F35)
1 x Flywheel Twin Disk 7.25in B2xx
1 x Aluminum Flywheel For NG900/9-3
1 x Transmission Nut F35 F25
1 x Alu Hybrid Flywheel For NG900/9-3
1 x c900 Performance Brake lines
1 x PPC - Upgrade from stage 1 to stage 3
1 x Clear Little Fender Blinkers Factory Saab
1 x 9-3 / 900 Uprated Suspension Bushings Inner
1 x 3pt Subframe Brace for 9-3 SS 2003-> 2wd
1 x 20th Viggen logo Shifter Top
1 x 5d Rear Window repair kit 94-02 900/9-3/9-5
1 x 9-3 / 900 Uprated Front ARB Bushings
1 x 9-5 Blend Flap Limit Lever 99-04
1 x T5 3.0 Bar Map Sensor Adaptor
1 x Intake Flange B2x4 T5
$7,228.56
Manufacturer Info
Taliaferro
Other products
Share Product
Share via E-Mail