$208.00 $156.00

Steering Rack Brace & Clamp Kit
[SRBK]

Steering Rack Brace & Clamp Kit

Add to Cart

Date Added: Thursday 07 April, 2011

by Steve Beisser

I bought a 2000 9-3 conv. 5 speed back in Sept. I love the car, but did not like some of the handling characteristics (major torque steer-which is really a problem when driving a 5 speed since only one hand is on the wheel when accelerating hard and winding through the gears, excessive body lean through turns, and cowel shake). I decided to buy this steering rack brace kit along with the rear sway bar. I ordered it on Monday and they arrived on Thursday. I just put in the steering rack brace and took it for a spin. All I can say is THANK YOU TALIAFERRO! The torque steer is GONE!. I do notice a slight more amount of road feel coming through the steering wheel, but i actually like this. Truth is, it is very minor and I only noticed it because I just installed the thing and was really trying to see what the differences were. The installation was not difficult (I was surprised that no instructions were provided but found the installation photos on this site). It took me about an hour to install. Some helpful hints. The upper strut brace gets in the way, so if you are planning on replacing that too it would make this job easier to remove the factory one, then install this rack brace, then install the new strut brace. I also found working on the lower bolt to be a bit of a challenge since you can't see it. One last thing to note. You do not have to remove the front right wheel as I have seen suggested in order to get at the nut on the bolt that goes through the wheel well, I just turned the wheel all the way to the left, which allowed me to put my 10 mm box wrench on the nut inside the wheel well and then reached over the fender to tighten the bolt with a 10 mm socket. Getting my torque wrench on the bolts was a challenge (upper strut brace gets in the way) but hopefully I got the torques OK. I will re-check after 100 miles as they suggest. Next on the list is the rear sway bar, then I plan on installing the upper strut brace and the 6 point sub frame brace. I plan on doing each upgrade one at a time and will report back the results. As far as this one goes - it's a no brainer. Everyone with this car needs to install this. In my opinion, it should be viewed as a safety feature (of course, it also increases the fun factor too!) It's hard to believe Saab let this model out of the factory without this.

Rating: 5 of 5 Stars! [5 of 5 Stars!]

Write Review Back
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
2 x Catback 2.5in Exh 9-3 99-02 Wide Oval Tip (NOT VIG)
3 x Exhaust Clamp Kit
3 x Exhaust manifold Stud Kit
2 x Catback 2.5in Exh 900/9-3 94-02 Round Tip
3 x Flex Pipe 900 94-98 9-3 99-02
3 x ARP Exhaust Manifold Stud kit Stainless
1 x Basic Subframe Brace
1 x Steering Coupler 9-3 99-02
2 x Limit Strap Coilover Add On Kit
2 x Rear spring perches Adjustable NG900/9-3
3 x 9-3 / 900 Uprated Suspension Bushings Inner
3 x PPC 3 Volvo Diagnostic System
3 x Rear Engine Mount 4cyl
1 x Fuel Line Clip
1 x Replacement Filter for Open air 9-3 T7
2 x Replacement Hardware Pack 6-Point
1 x Mass Airflow Meter T7
1 x Crank Vent Kit #6 T7 4cyl
1 x Direct Ignition T5 RED
1 x Genuine Saab 4cyl Oil Filters
1 x Downpipe Hardware Kit
1 x Direct Ignition T7 Black
1 x 5d Rear Window repair kit 94-02 900/9-3/9-5
2 x IAT Weld Bung T5/Bosch
1 x Header Flange Stainless Blended Transition B2x4,B2x5
1 x Moog Ball Joint
1 x PPC - Upgrade from stage 1 to stage 3
1 x Map/MAT sensor weld bung
1 x Header Flange 1/2in Blended Transition B2x4,B2x5
1 x Universal / Special Request
1 x T7 Head Plug NGK
1 x JE Piston Ring (1cyl) 90.5mm 235/205/204
1 x Alu Hybrid Flywheel For NG900/9-3
1 x Head Stud Kit all 4cyl
1 x Headbolts (New Style)
1 x Slave Cyl
1 x Short Shifter NG900/9-3 94-02/9-5 (Outright Kit)
1 x JE Piston Rings 90.0mm 235/205
1 x Oil Filter Re-locator
1 x Balance Shaft Tensioner Delete
2 x Quaife Differential 9-5 and Viggen (F35)
1 x Transmission Nut F35 F25
1 x Replacement Flywheel Insert NG900/9-3
2 x Shift Rod Bushings
3 x Shifter Top Ghost Logo
1 x Rod Bearings only Pauter Rods
1 x Sport Transmission Mount 9-3/900 (Automatic)
1 x 4340 Connecting Rods B204 B235
1 x Aluminum Flywheel For NG900/9-3
1 x 3pt Subframe Brace for 9-3 SS 2003-> 2wd
1 x 9-5 Blend Flap Limit Lever 99-04
1 x Viggen Titanium KeyChain
1 x Floormats BSR 9-3 99-02 900 94-98
1 x Open Air Intake 9-3 00-02 and Viggen (All T7)
1 x ATF Saab 3309 (Automatic 02->)
1 x 9-5 Aero Sill Protection
1 x BSR Optiflow Intake 4cyl w SAI
1 x Troll Head Plug
1 x Upgrade Valve Springs T5 Cars
1 x Forge Turbo Bypass Valve 9-3SS 2.0t 175hp
1 x Cat Back Exh Dual Exit for 9-3 SS/SC 2.8t
1 x Coreganizer
1 x Griffin logo Shifter Top
1 x Spec Light Flywheel For 9-5 4cyl 99-09
1 x Sport Transmission Mount 9-5 (Manual) 1998-1999
1 x 9-5 Wheel 10-Spoke 16in.
2 x Rear Camber Shims Kit 6pcs
1 x V6 Tank Float - SparePart
1 x Front Camber Adjustment Bolts
$16,197.94
Manufacturer Info
Taliaferro
Other products
Share Product
Share via E-Mail