$208.00 $156.00

Steering Rack Brace & Clamp Kit
[SRBK]

Steering Rack Brace & Clamp Kit

Add to Cart

Date Added: Thursday 07 April, 2011

by Steve Beisser

I bought a 2000 9-3 conv. 5 speed back in Sept. I love the car, but did not like some of the handling characteristics (major torque steer-which is really a problem when driving a 5 speed since only one hand is on the wheel when accelerating hard and winding through the gears, excessive body lean through turns, and cowel shake). I decided to buy this steering rack brace kit along with the rear sway bar. I ordered it on Monday and they arrived on Thursday. I just put in the steering rack brace and took it for a spin. All I can say is THANK YOU TALIAFERRO! The torque steer is GONE!. I do notice a slight more amount of road feel coming through the steering wheel, but i actually like this. Truth is, it is very minor and I only noticed it because I just installed the thing and was really trying to see what the differences were. The installation was not difficult (I was surprised that no instructions were provided but found the installation photos on this site). It took me about an hour to install. Some helpful hints. The upper strut brace gets in the way, so if you are planning on replacing that too it would make this job easier to remove the factory one, then install this rack brace, then install the new strut brace. I also found working on the lower bolt to be a bit of a challenge since you can't see it. One last thing to note. You do not have to remove the front right wheel as I have seen suggested in order to get at the nut on the bolt that goes through the wheel well, I just turned the wheel all the way to the left, which allowed me to put my 10 mm box wrench on the nut inside the wheel well and then reached over the fender to tighten the bolt with a 10 mm socket. Getting my torque wrench on the bolts was a challenge (upper strut brace gets in the way) but hopefully I got the torques OK. I will re-check after 100 miles as they suggest. Next on the list is the rear sway bar, then I plan on installing the upper strut brace and the 6 point sub frame brace. I plan on doing each upgrade one at a time and will report back the results. As far as this one goes - it's a no brainer. Everyone with this car needs to install this. In my opinion, it should be viewed as a safety feature (of course, it also increases the fun factor too!) It's hard to believe Saab let this model out of the factory without this.

Rating: 5 of 5 Stars! [5 of 5 Stars!]

Write Review Back
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
4 x Intake Flange B2x4 T5
3 x Moog Ball Joint
4 x Limit Strap Coilover Add On Kit
1 x Injectors Siemens 80lb 875cc (set 4)
3 x Injectors Green Giant 42lb (set 4)
1 x IAT Weld Bung T5/Bosch
1 x Rivetnuts Pair (2pcs)
1 x AEM Wideband Gauge Kit
2 x Injectors Siemens 60lb 630cc (set 4)
3 x Header Flange 1/2in Blended Transition B2x4,B2x5
4 x Downpipe Flange Assy. Stainless T25/Td04 to 3in
1 x Header Flange Stainless Blended Transition B2x4,B2x5
1 x Universal / Special Request
1 x Viggen Titanium KeyChain
2 x Clear Little Fender Blinkers Factory Saab
3 x c900 Performance Brake lines
3 x Rear Camber Shims Kit 6pcs
1 x 9-3 ng900 radio wires
2 x Shifter Mount Kit Cobalt/ HHR
2 x Oil Cap GM "HHR"
1 x Short Shifter HHR Cobalt F35 F40
1 x 5d Rear Window repair kit 94-02 900/9-3/9-5
1 x 3pt Subframe Brace for 9-3 SS 2003-> 2wd
1 x 9-3 / 900 Uprated Front ARB Bushings
1 x 9-3 / 900 Uprated Suspension Bushings Inner
2 x 9-5 Blend Flap Limit Lever 99-04
2 x Midpipe 2.0T 07-11 FWD (2wd)
2 x 20th Viggen logo Shifter Top
2 x Shift Rod Bushings
3 x Basic Subframe Brace
2 x T5 3.0 Bar Map Sensor Adaptor
3 x PPC - Upgrade from stage 1 to stage 3
1 x Head Bolt Washers
1 x Fuel Pressure Regulator 4.0 bar
3 x Griffin logo Shifter Top
1 x BSR 9-5 3.0T V6 200Hp
1 x Transmission Nut F35 F25
1 x Crush Sleeve F35 F25
2 x 9000 Shifter Bushing Repair Kit
1 x BSR 9-5 Aero 250Hp 2004-2005 Stage E85
2 x BSR 9-5 260Hp 2006-
1 x 9-5 Aero Sill Protection
1 x Open Air Intake 9-3 00-02 and Viggen (All T7)
3 x B207 Coolant Cap
1 x Alu Hybrid Flywheel For NG900/9-3
2 x T7 Head Plug NGK
1 x Turbo to Downpipe Flange B207
1 x Exhaust manifold Stud Kit
1 x Rear spring perches Adjustable NG900/9-3
1 x Oil Cap 9-3SS V6 "Ghost"
1 x Oil Cap 9-3SS "Ghost"
1 x B207 Upper Radiator Coolant T
1 x Forge Bypass Valve Cobalt/HHR TC
1 x Brake Vac pump seals
1 x ShortShift Kit 93ss
1 x Short Shifter NG900/9-3 94-02/9-5 (Outright Kit)
1 x Storage Tray / Ashtray Kit 9-5 10-
1 x Brembo Kit 315mm Hawk HPS Pads
1 x Rear Brake Pads 9-3 SS
1 x Front Rotors PAIR 285mm Plain (Code: AA)
1 x Rear Rotors PAIR 278mm Plain (Code: BA)
1 x 9-3 SS Akebono Rear Pads
1 x Rear Rotors PAIR 292mm Plain (Code: BB)
1 x Ceramic Low Dust Brake Pads 9-3 SS
1 x Goodridge Brake Lines 9-3 SS / SC 03-
1 x Troll Head Plug
2 x Mat Set Black Rubber 9-5 10-
1 x MTF0063 Manual Gear oil
1 x Map/MAT sensor weld bung
$12,600.72
Manufacturer Info
Taliaferro
Other products
Share Product
Share via E-Mail