$208.00 $156.00

Steering Rack Brace & Clamp Kit
[SRBK]

Steering Rack Brace & Clamp Kit

Add to Cart

Date Added: Thursday 07 April, 2011

by Steve Beisser

I bought a 2000 9-3 conv. 5 speed back in Sept. I love the car, but did not like some of the handling characteristics (major torque steer-which is really a problem when driving a 5 speed since only one hand is on the wheel when accelerating hard and winding through the gears, excessive body lean through turns, and cowel shake). I decided to buy this steering rack brace kit along with the rear sway bar. I ordered it on Monday and they arrived on Thursday. I just put in the steering rack brace and took it for a spin. All I can say is THANK YOU TALIAFERRO! The torque steer is GONE!. I do notice a slight more amount of road feel coming through the steering wheel, but i actually like this. Truth is, it is very minor and I only noticed it because I just installed the thing and was really trying to see what the differences were. The installation was not difficult (I was surprised that no instructions were provided but found the installation photos on this site). It took me about an hour to install. Some helpful hints. The upper strut brace gets in the way, so if you are planning on replacing that too it would make this job easier to remove the factory one, then install this rack brace, then install the new strut brace. I also found working on the lower bolt to be a bit of a challenge since you can't see it. One last thing to note. You do not have to remove the front right wheel as I have seen suggested in order to get at the nut on the bolt that goes through the wheel well, I just turned the wheel all the way to the left, which allowed me to put my 10 mm box wrench on the nut inside the wheel well and then reached over the fender to tighten the bolt with a 10 mm socket. Getting my torque wrench on the bolts was a challenge (upper strut brace gets in the way) but hopefully I got the torques OK. I will re-check after 100 miles as they suggest. Next on the list is the rear sway bar, then I plan on installing the upper strut brace and the 6 point sub frame brace. I plan on doing each upgrade one at a time and will report back the results. As far as this one goes - it's a no brainer. Everyone with this car needs to install this. In my opinion, it should be viewed as a safety feature (of course, it also increases the fun factor too!) It's hard to believe Saab let this model out of the factory without this.

Rating: 5 of 5 Stars! [5 of 5 Stars!]

Write Review Back
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
3 x Shifter Mount Kit Cobalt/ HHR
3 x Universal / Special Request
4 x Clear Little Fender Blinkers Factory Saab
3 x Head Bolt Washers
3 x Map/MAT sensor weld bung
3 x IAT Weld Bung T5/Bosch
3 x c900 Performance Brake lines
2 x Fuel Pressure Regulator 4.0 bar
3 x T5 3.0 Bar Map Sensor Adaptor
4 x Floormats BSR 9-3SS/SC
1 x PPC 3 Volvo Diagnostic System
3 x Goodridge Brake Lines 9-3 SS / SC 03-
2 x 3 Point Hardware
1 x Shifter Mount Kit 93ss
1 x Front Camber Adjustment Bolts
1 x Torque Mount Insert V6 Manual (XWD and FWD)
1 x ShortShift Kit 93ss
1 x 3pt Subframe Brace for 9-3 SS 2003-> 2wd
1 x ATF Saab 3309 (Automatic 02->)
1 x Forge Turbo Bypass Valve 9-3SS 2.0T 210hp
2 x MTF0063 Manual Gear oil
2 x Shifter Alignment Pins (Set 2)
1 x 9000 Shifter Bushing Repair Kit
1 x Forge Bypass Valve Cobalt/HHR TC
2 x Basic Subframe Brace
2 x Header Flange Stainless Blended Transition B2x4,B2x5
2 x Weld Bungs -Taper- Race Only
1 x Custom Brake Lines Brembo 315mm 9-3SS/SC
1 x Injectors Siemens 60lb 630cc (set 4)
1 x PPC - Upgrade from stage 1 to stage 3
2 x 9000 High Performance Brake Line Kit '95-'98
1 x Performance Brake Line Kit NG900 94-98 9-3 99-02
1 x Injectors Green Giant 42lb (set 4)
2 x Header Flange 1/2in Blended Transition B2x4,B2x5
1 x Custom Brake Lines RR 300mm Kit
1 x 9-5 High Performance Brake Line Kit
1 x 9-5 Aero Sill Protection
1 x Moog Ball Joint
4 x Metal Steering Wheel Buttons
2 x Shift Rod Bushings
1 x Turbo to Downpipe Flange B207
1 x InjectorDynamics 725cc For 2.8V6 (Set6)
1 x v6 header flange
1 x Oil Cap 9-3SS "Ghost"
1 x Midpipe 2.8T FWD (2wd)
1 x Midpipe 2.0T 07-11 FWD (2wd)
1 x Oil Cap 9-3SS V6 "Griffin"
2 x Exhaust manifold Stud Kit
2 x Hawk HPS FRONT Pads 9-3 TurboX (345mm)
1 x Front Rotors PAIR 302mm Plain (Code: AB)
2 x Genuine Saab 4cyl Oil Filters
1 x 9-3 /NG900 Grille
1 x 9-5 Wheel 5-Spoke Twin 17in
3 x Open Air Intake 9000 93-98
1 x 9-5 Shift Knobs Leather
1 x Machined Control Arm Kit
1 x 9-3 ng900 Hood Protection Strip
1 x v6oilcoolplate
1 x 9-3 / 900 Uprated Suspension Bushings Inner
2 x 9-3SS Wheel 5-Spoke Low Split 17 in.
1 x Rivetnuts Pair (2pcs)
1 x AEM Wideband Gauge Kit
1 x BSR Optiflow Intake 4cyl
1 x Short Shifter HHR Cobalt F35 F40
1 x Downpipe Flange Assy. Stainless T25/Td04 to 3in
1 x Downpipe Hardware Kit
1 x 9000 Intercooler ETS
1 x ARP Exhaust Manifold Stud kit Stainless
1 x Cat Back Exh for 9000 CS, CSE AERO
1 x Brake Vac pump seals
1 x Cat Back Exh for 9-3 SS 03-06, CV04-06 Stainless
2 x Downpipe 2.8T FWD (2wd)
1 x Ignition Coil 9-3SS 2.0t and 2.0T
1 x Coreganizer
1 x Adaptor Harness Handsfree 01-
1 x Steering Rod Bushings NG900/93
1 x Steering Coupler 9-3 99-02
1 x BSR Optiflow Replacement Filter V6 2.8
1 x Mass Airflow Meter T7
1 x Hood Emblem 9-5 All
1 x Headlight Connector Repair Kit 9-3SS 9-5
1 x Hood Emblem 9-3 SS/sc 03- All
1 x Fuel Line Clip
1 x Mat Set Textile Shark Grey 9-5 10-
1 x BSR PPC 9-3 SS/SC 2.0T 210hp 2007-->
1 x Troll Head Plug
1 x Flex Pipe 900 94-98 9-3 99-02
$15,971.74
Manufacturer Info
Taliaferro
Other products
Share Product
Share via E-Mail