$100.00 $90.00

Rear Anti-Roll (anti Sway) Bar NG900 / 9-3
[ARB22]

Rear Anti-Roll (anti Sway) Bar NG900 / 9-3

Add to Cart

Date Added: Wednesday 07 April, 2010

by Gerrit vanNieuwenhuizen

I don't have an LSD, but I just got a 22mm rear swaybar installed on my Viggen. For US$90 I think that is a much better investment than an expensive Quaife. Nick Taliaferro has already mentioned this on his website, it looks like that the loss of traction on the left or right front wheel is for big part due to the rear end of the Viggen not being stiff enough. The twisting in the back makes the front wheels lose contact on full throttle and the car moves left or right. This has been interpreted like torque steer or tramlining. I had my doubts about the torque steer because my car kind of oscillated between going left and right under full acceleration, even on a perfect road. With torque steer you expect the car to keep trying to move in one direction only, depending on the slight difference that the left and right drive train experience at that moment.

Unfortunately I also installed the GenuineSaab sport front and rear engine mounts and the sport transmission mount at the same time. So, it is a bit difficult to judge the effect of the fat rear swaybar alone. However, the effect of the whole setup is amazing! The car goes straight even under full torque load! Don't try this at home, but I even took my hands off the steering wheel when accelerating and the car keeps going dead straight.
Also in long sharp curves the car now behaves much better. The swaybar does what it is meant for, i.e. keeping the car more flat. I also notice that I can now accelerate much more through corners, the understeer is much less but there is still enough left to not be surprised by a sudden oversteer.

GenuineSaab has been selling stiffer sport front engine and transmission mounts for a while now. The sport rear engine mount is new. These are not race mounts, the urethane bushings still give some cushioning but they are much, much stiffer than the originals. Imho, the originals are crap for a Viggen engine. After only 60,000 miles mine were pretty much shot and I could feel and hear the engine moving around. The new mounts keep the engine much better in place and the whole setup feels much tighter. The shift stick doesn't move by itself anymore and, probably because all the slop is gone, the car now responds much more acute to the throttle.
The price that you are paying for this is a bit more vibration and noise in the cabin. The vibration is hardly noticeable. The noise is just the that sound of the engine gets transmitted more to the car chassis and into the cabin. I find it totally not disturbing, it is just that you hear the engine growling under acceleration, it doesn't drown out conversation or your stereo. So, you get for free what Ford is trying to do with the Mustang, i.e. piping engine sound into the cabin.

Highly recommended to increase driving fun.

Rating: 5 of 5 Stars! [5 of 5 Stars!]

Write Review Back
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x Clear Little Fender Blinkers Factory Saab
1 x Viggen Titanium KeyChain
1 x SCNA Christmas Calendar
1 x Saab black Keychain
1 x Shifter Mount Kit Cobalt/ HHR
1 x Forge Bypass Valve Cobalt/HHR TC
1 x Short Shifter HHR Cobalt F35 F40
1 x Oil Cap GM "HHR"
1 x Fuel Pressure Regulator 4.0 bar
1 x Map/MAT sensor weld bung
1 x Injectors Siemens 80lb 875cc (set 4)
2 x 9-5 Aero Sill Protection
2 x Fuel Line Clip
1 x Cat Back Exh for 9-3 SS 03-06, CV04-06 Stainless
1 x Throttle Bend for T5 94-99
1 x BSR Optiflow Intake V6 2.8t
1 x Open Air Intake 9-3 00-02 and Viggen (All T7)
1 x Midpipe 2.0T 07-11 FWD (2wd)
1 x Cat Back Exh Dual Exit for 9-3 SS/SC 2.8t
2 x Genuine Saab 4cyl Oil Filters
1 x Downpipe 2.8T XWD (4wd)
1 x BSR PPC 9-3 SS/SC 2.0T 210hp 2007-->
1 x Turbo Conversion Pipe 900 9-3 T5
1 x T7 Injector Spacer Kit
1 x Downpipe Hardware Kit
1 x Downpipe 2.8T FWD (2wd)
2 x Adaptor Harness Handsfree 01-
1 x Rear Pedestal Spoiler 9-3 SS
2 x Flex Pipe 900 94-98 9-3 99-02
1 x Replacement Filter for Open air 9-3 T7
2 x 9-3/NG900 Shift Knobs Leather
1 x Forge Turbo Bypass Valve 9-3SS 2.0t 175hp
1 x BSR PPC 9-3 SS/SC TurboX and XWD 2.8T V6 280hp
2 x 5d Rear Window repair kit 94-02 900/9-3/9-5
2 x Floormats BSR 9-3 99-02 900 94-98
1 x Con Rods V6 2.8L 155.8mm
1 x Replacement Hardware Pack 6-Point
1 x Brake Vac pump seals
1 x Oil Filter Re-locator
1 x Catback 2.5in Exh 9-3 99-02 Wide Oval Tip (NOT VIG)
1 x Torque Mount Insert V6 Manual (XWD and FWD)
1 x Slave Cyl
1 x Short Shifter NG900/9-3 94-02/9-5 (Outright Kit)
1 x Flywheel Twin Disk 7.25in B2xx
1 x Aluminum Flywheel For NG900/9-3
1 x 3 Point Hardware
1 x Balance Shaft Tensioner Delete
1 x Basic Subframe Brace
1 x JE Piston Ring (1cyl) 90.5mm 235/205/204
1 x ARP Exhaust Manifold Stud kit Stainless
1 x Shifter Top Ghost Logo
1 x Sport Transmission Mount 9-3/900 (Automatic)
1 x 9-5 Textile Mats 98-07
2 x 3pt Subframe Brace for 9-3 SS 2003-> 2wd
1 x Shifter Mount Kit 93ss
1 x Catback 2.5in Exh 900/9-3 94-02 Round Tip
1 x Cat back for Viggen 2.5in
1 x PPC - Upgrade from stage 1 to stage 3
1 x 9-5 Blend Flap Limit Lever 99-04
2 x 20th Viggen logo Shifter Top
1 x 9-3 / 900 Uprated Suspension Bushings Inner
1 x 9-3 / 900 Uprated Front ARB Bushings
1 x Crush Sleeve F35 F25
1 x BSR Optiflow Intake 4cyl
1 x T7 3.5 Bar Fuel Pressure Regulator
1 x Turbo Bypass Valve
1 x Coreganizer
1 x 9-3 Rear Ashtray
1 x Exhaust Clamp Kit
1 x Throttle Body T7
1 x Remote Button NG900
1 x Mass Airflow Meter T7
1 x Exhaust manifold Stud Kit
1 x Rear Brake Pads 9-3 SS
$13,513.49
Manufacturer Info
Taliaferro
Other products
Share Product
Share via E-Mail