$20.00

Steering Rod Bushings NG900/93
[4242669U]

Steering Rod Bushings NG900/93

Add to Cart

Date Added: Monday 28 July, 2014

by Mark Storms

What an awesome little upgrade. Much tighter steering response. If I had a complaint, the steering is a little too light now. The bushings don't deflect as the angle of the arm changes now, therefore the resistance at the bolt is lower. With the drastically improved response, I find myself over correcting entering a corner or avoiding a pothole. Early apexes everywhere, but I'll get past it.

Install: Take the two bolts out of the arms at the center of the rack. Remove the stealthy sheet-metal spring washer thing that locks both bolts in place first. Be aware, there are two washers between the arms and the rack. Don't drop the washers when you take out the two bolts. They will likely fall down and get lost out of sight on the cross member below. Since you didn't raise the car for this job and now you can't drive it from the driveway to the shop, it'll take you longer than the rest of the install to find them... I know. The old bushings came out hard(ish) at 110 K. I used a set of medium channel locks and some WD40. Make sure the holes are clean, dry, and rust free and install the new bushings. Install the arms in reverse and you're done. The whole thing lasts about 20 minutes without losing the washers... an hour if you do.

Rating: 5 of 5 Stars! [5 of 5 Stars!]

Write Review Back
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
1 x v6 header flange
1 x v6oilcoolplate
1 x Short Shifter NG900/9-3 94-02/9-5 (Outright Kit)
1 x Rivetnuts Pair (2pcs)
1 x Injectors Green Giant 42lb (set 4)
1 x Head Bolt Washers
1 x Moog Ball Joint
2 x AEM Wideband Gauge Kit
1 x Header Flange Stainless Blended Transition B2x4,B2x5
2 x Injectors Siemens 80lb 875cc (set 4)
1 x Weld Bungs -Taper- Race Only
1 x PPC - Upgrade from stage 1 to stage 3
1 x Injectors Siemens 60lb 630cc (set 4)
1 x IAT Weld Bung T5/Bosch
1 x Fuel Pressure Regulator 4.0 bar
1 x Header Flange 1/2in Blended Transition B2x4,B2x5
1 x Downpipe Flange Assy. Stainless T25/Td04 to 3in
1 x Midpipe 2.0T 07-11 FWD (2wd)
1 x 5d Rear Window repair kit 94-02 900/9-3/9-5
1 x 9-5 Blend Flap Limit Lever 99-04
1 x Forge Turbo Bypass Valve 9-3SS 2.0T 210hp
1 x Catback 2.5in Exh 9-3 99-02 Wide Oval Tip (NOT VIG)
1 x Viggen Fog Air Intake
1 x Midpipe 2.8T FWD (2wd)
1 x Floormats BSR 9-3 99-02 900 94-98
1 x Downpipe 2.8T XWD (4wd)
1 x Rear spring perches Adjustable NG900/9-3
1 x Torque Mount Insert V6 Manual (XWD and FWD)
1 x Rod Bearings only Pauter Rods
1 x Shifter Top Ghost Logo
2 x Flywheel Twin Disk 7.25in B2xx
1 x Optical Cable Connector (Onstar Delete)
1 x Exhaust Clamp Kit
1 x Machined Control Arm Kit
1 x 9-3 / 900 Uprated Front ARB Bushings
1 x Steering Rod Bushings NG900/93
1 x Mass Airflow Meter T7
1 x Troll Titanium KeyChain
1 x T5 3.0 Bar Map Sensor Adaptor
1 x Map/MAT sensor weld bung
1 x Midpipe 2.8T XWD (4wd)
1 x Mat Set Textile Parchment 9-5 10-
1 x Downpipe Hardware Kit
$7,275.13
Manufacturer Info
Taliaferro
Other products
Share Product
Share via E-Mail