$65.00

9-3/NG900 Manual Billet Pedals
[0109443]

9-3/NG900 Manual Billet Pedals

Add to Cart

Date Added: Tuesday 13 November, 2012

by James Nakatsu

Opted for the blasted Aluminium due to the carpet being weathered and not exactly black.
Apparently, the factory pedal extensions are installe dthe same way, but I didn't know how to install the extensions...
Pics and a small description can be found on the Saab Club of Seattle facebook page.

Remove the factory pedals (I cut them with a box-cutter).
Place a wood block under the pedal for a solid surface to drill.
I fixed the pedals with 3M moulding adhesive tape and drilled.
I drilled with the pedals in place to use the pedals as a guide.
(wear goggles and use a paper towel to catch shavings)
3/16" bit is a bit tight, but wriggling it will enlarge the hole.
Pop the hex screw in, secure nut with 8mm wrench.
Tighten the hex screw with drill with slow, low torque setting.
Proceed to diagonally opposing holes for good results.
Check alignment of pedal frequently.
I ended up leaving the 3M tape under the pedal (laziness).

The materials and the grooves grip your feet quite nicely. Purposefully built and it looks good, nestled in the driver's footwell.
Installation took about 30 minutes. The first hole is a nervous one - subsequent ones are a breeze.
requires you to remove the sill, peel back the rubber seal, and the carpet a bit.

Rating: 5 of 5 Stars! [5 of 5 Stars!]

Write Review Back
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
3 x Saab black Keychain
1 x Viggen Titanium KeyChain
3 x Intake Flange B2x4 T5
1 x T5 3.0 Bar Map Sensor Adaptor
1 x PPC - Upgrade from stage 1 to stage 3
2 x Header Flange 1/2in Blended Transition B2x4,B2x5
1 x Map/MAT sensor weld bung
1 x Moog Ball Joint
2 x Injectors Green Giant 42lb (set 4)
1 x Head Bolt Washers
1 x AEM Wideband Gauge Kit
1 x Fuel Pressure Regulator 4.0 bar
1 x Downpipe Flange Assy. Stainless T25/Td04 to 3in
1 x IAT Weld Bung T5/Bosch
1 x Universal / Special Request
4 x Forge Bypass Valve Cobalt/HHR TC
1 x Oil Cap GM "HHR"
1 x BSR Optiflow Intake Volvo S60 I T5 2001-2004
1 x Con Rods V6 2.8L 155.8mm
1 x Replacement V6 Coolant Cap
1 x Limit Strap Coilover Add On Kit
3 x T7 Head Plug NGK
1 x Clear Little Fender Blinkers Factory Saab
1 x 9-5 Aero Sill Protection
1 x 9-3/NG900 Shift Knobs Leather
1 x 9-5 Rear Brake rotor See Description
1 x Antenna Plug NG900/9-3 hatchback
2 x MTF0063 Manual Gear oil
1 x Floormats BSR 9-3 99-02 900 94-98
1 x Griffin logo Shifter Top
1 x Rear Pedestal Spoiler 9-3 SS
1 x BSR PPC 9-3 SS/SC TurboX and XWD 2.8T V6 280hp
2 x Headbolts (New Style)
2 x ARP Exhaust Manifold Stud kit Stainless
1 x 9-5 Textile Mats 98-07
1 x 5d Rear Window repair kit 94-02 900/9-3/9-5
2 x Balance Shaft Tensioner Delete
2 x Shifter Mount Kit Cobalt/ HHR
1 x Catback 2.5in Exh 900/9-3 94-02 Round Tip
1 x 9-3 ng900 radio wires
2 x Head Stud Kit all 4cyl
1 x Exhaust manifold Stud Kit
2 x Brake Vac pump seals
2 x Forge Turbo Bypass Valve 9-3SS 2.0t 175hp
2 x Forge Turbo Bypass Valve 9-3SS 2.0T 210hp
1 x Adaptor Harness Handsfree 01-
1 x 3 Point Hardware
1 x Midpipe 2.0T 07-11 FWD (2wd)
1 x Brembo Kit 315mm Hawk HPS Pads
2 x Shift Rod Bushings
1 x 9000 Intercooler ETS
1 x Upgrade Valve Springs T5 Cars
1 x 9-3 900 9-5 REAR Brembo Disk See Descr.
1 x B207 Coolant Cap
1 x Crush Sleeve F35 F25
1 x Hawk HPS FRONT Pads 9-3 9-5 (900 97-98)
1 x 9000 Shifter Bushing Repair Kit
1 x Troll Head Plug
1 x 9-5 Exhaust Flex Pipe Stainless
1 x Oil Filter Re-locator
1 x Rod Bearings only Pauter Rods
1 x BSR 9-5 2010-2011 V6 300Hp
1 x JE Piston Rings 90.0mm 235/205
1 x K&N Filter Service Kit
$10,690.48
Manufacturer Info
Taliaferro
Other products
Share Product
Share via E-Mail