$208.00 $156.00

Steering Rack Brace & Clamp Kit
[SRBK]

Steering Rack Brace & Clamp Kit

Add to Cart

Date Added: Thursday 07 April, 2011

by Steve Beisser

I bought a 2000 9-3 conv. 5 speed back in Sept. I love the car, but did not like some of the handling characteristics (major torque steer-which is really a problem when driving a 5 speed since only one hand is on the wheel when accelerating hard and winding through the gears, excessive body lean through turns, and cowel shake). I decided to buy this steering rack brace kit along with the rear sway bar. I ordered it on Monday and they arrived on Thursday. I just put in the steering rack brace and took it for a spin. All I can say is THANK YOU TALIAFERRO! The torque steer is GONE!. I do notice a slight more amount of road feel coming through the steering wheel, but i actually like this. Truth is, it is very minor and I only noticed it because I just installed the thing and was really trying to see what the differences were. The installation was not difficult (I was surprised that no instructions were provided but found the installation photos on this site). It took me about an hour to install. Some helpful hints. The upper strut brace gets in the way, so if you are planning on replacing that too it would make this job easier to remove the factory one, then install this rack brace, then install the new strut brace. I also found working on the lower bolt to be a bit of a challenge since you can't see it. One last thing to note. You do not have to remove the front right wheel as I have seen suggested in order to get at the nut on the bolt that goes through the wheel well, I just turned the wheel all the way to the left, which allowed me to put my 10 mm box wrench on the nut inside the wheel well and then reached over the fender to tighten the bolt with a 10 mm socket. Getting my torque wrench on the bolts was a challenge (upper strut brace gets in the way) but hopefully I got the torques OK. I will re-check after 100 miles as they suggest. Next on the list is the rear sway bar, then I plan on installing the upper strut brace and the 6 point sub frame brace. I plan on doing each upgrade one at a time and will report back the results. As far as this one goes - it's a no brainer. Everyone with this car needs to install this. In my opinion, it should be viewed as a safety feature (of course, it also increases the fun factor too!) It's hard to believe Saab let this model out of the factory without this.

Rating: 5 of 5 Stars! [5 of 5 Stars!]

Write Review Back
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
15 x Cat Back Exh for 9-3 SS 03-06, CV04-06 Stainless
3 x Con Rods V6 2.8L 155.8mm
3 x Downpipe 2.8T XWD (4wd)
4 x Midpipe 2.0T 07-11 FWD (2wd)
1 x Downpipe 2.8T FWD (2wd)
1 x BSR Optiflow Intake V6 2.8t
3 x Injectors 175hp Stg3 (Set4)
1 x BSR Optiflow Replacement Filter V6 2.8
2 x InjectorDynamics 725cc For 2.8V6 (Set6)
3 x Cat Back Exh Dual Exit for 9-3 SS/SC 2.8t
3 x Forge Turbo Bypass Valve 9-3SS 2.0t 175hp
5 x BSR Optiflow Intake 4cyl w SAI
3 x Midpipe 2.8T XWD (4wd)
4 x BSR Optiflow Intake 4cyl
4 x v6 2.8t SAI Delete Kit
4 x v6oilcoolplate
3 x Turbo to Downpipe Flange B207
4 x Oil Cap 9-3SS "Ghost"
4 x Oil Cap 9-3SS V6 "Griffin"
4 x v6 header flange
1 x ShortShift Kit 93ss
1 x Shifter Mount Kit 93ss
2 x 3pt Subframe Brace for 9-3 SS 2003-> 2wd
2 x Front Camber Adjustment Bolts
1 x Torque Mount Insert V6 Manual (XWD and FWD)
2 x 9-3 ng900 radio wires
1 x Shifter Alignment Pins (Set 2)
1 x ATF Saab 3309 (Automatic 02->)
3 x Saab black Keychain
1 x Viggen Titanium KeyChain
1 x PPC 3 Volvo Diagnostic System
1 x Headbolts (New Style)
2 x BSR Optiflow Intake Volvo S60 I T5 2001-2004
1 x 4340 Connecting Rods B204 B235
1 x BSR PPC 9-3 SS/SC 2.0T 210hp 2007-->
1 x Catback 2.5in Exh 9-3 99-02 Wide Oval Tip (NOT VIG)
1 x Direct Ignition T7 Black
2 x Crush Sleeve F35 F25
1 x Rear spring perches Adjustable NG900/9-3
1 x Remote Button NG900
1 x Turbo Conversion Pipe 900 9-3 T5
5 x Forge Turbo Bypass Valve 9-3SS 2.0T 210hp
2 x 20th Viggen logo Shifter Top
1 x 9-5 Blend Flap Limit Lever 99-04
1 x 9-3 / 900 Uprated Suspension Bushings Inner
1 x 5d Rear Window repair kit 94-02 900/9-3/9-5
1 x 9-3 / 900 Uprated Front ARB Bushings
1 x MTF0063 Manual Gear oil
1 x 9-5 Wheel 5-Spoke Twin 17in
2 x 9-5 Aero Sill Protection
1 x 9-3/NG900 Shift Knobs Leather
1 x 9-5 Textile Mats 98-07
1 x 9-3SS Wheel 5-Spoke Low Split 17 in.
1 x 9-5 Shift Knobs Leather
1 x Air Filter 06 version (All 9-5)
1 x 9-5 AERO 308mm Front Brake Rotor / Disk
1 x Rear Rotors PAIR 292mm XWD (Code: BC)
1 x Griffin logo Shifter Top
1 x Brake Vac pump seals
1 x Shift Rod Bushings
1 x 4 Cyl 2.0 Coolant Tank
1 x Front Rotors PAIR 302mm Plain (Code: AB)
1 x Hawk HPS FRONT Pads 9-3 TurboX (345mm)
1 x Custom Brake Lines Brembo 315mm 9-3SS/SC
1 x Replacement Flywheel Insert NG900/9-3
1 x Rear Brake Pads 900 97-98, 9-3 99-02+ 03CV
1 x Custom Brake Lines RR 300mm Kit
1 x Header Flange Stainless Blended Transition B2x4,B2x5
1 x Machined Control Arm Kit
1 x Oil Filter Re-locator
1 x Flywheel Twin Disk 7.25in B2xx
1 x Head Bolt Washers
1 x Intake Flange B2x4 T5
1 x Moog Ball Joint
1 x Oil Cap GM "HHR"
1 x 9-5 Exhaust Flex Pipe Stainless
1 x Rear Camber Shims Kit 6pcs
1 x IAT Weld Bung T5/Bosch
1 x Oil Cooler Adaptor B2X5
1 x Oil Cap 9-3SS V6 "Ghost"
1 x Steering Coupler 9-3 99-02
1 x 3 Point Hardware
1 x Exhaust manifold Stud Kit
1 x B207 Upper Radiator Coolant T
1 x Alu Hybrid Flywheel For NG900/9-3
1 x Transmission Nut F35 F25
1 x V6 Tank Float - SparePart
1 x T5 3.0 Bar Map Sensor Adaptor
$34,839.25
Manufacturer Info
Taliaferro
Other products
Share Product
Share via E-Mail