$208.00 $156.00

Steering Rack Brace & Clamp Kit
[SRBK]

Steering Rack Brace & Clamp Kit

Add to Cart

Date Added: Thursday 07 April, 2011

by Steve Beisser

I bought a 2000 9-3 conv. 5 speed back in Sept. I love the car, but did not like some of the handling characteristics (major torque steer-which is really a problem when driving a 5 speed since only one hand is on the wheel when accelerating hard and winding through the gears, excessive body lean through turns, and cowel shake). I decided to buy this steering rack brace kit along with the rear sway bar. I ordered it on Monday and they arrived on Thursday. I just put in the steering rack brace and took it for a spin. All I can say is THANK YOU TALIAFERRO! The torque steer is GONE!. I do notice a slight more amount of road feel coming through the steering wheel, but i actually like this. Truth is, it is very minor and I only noticed it because I just installed the thing and was really trying to see what the differences were. The installation was not difficult (I was surprised that no instructions were provided but found the installation photos on this site). It took me about an hour to install. Some helpful hints. The upper strut brace gets in the way, so if you are planning on replacing that too it would make this job easier to remove the factory one, then install this rack brace, then install the new strut brace. I also found working on the lower bolt to be a bit of a challenge since you can't see it. One last thing to note. You do not have to remove the front right wheel as I have seen suggested in order to get at the nut on the bolt that goes through the wheel well, I just turned the wheel all the way to the left, which allowed me to put my 10 mm box wrench on the nut inside the wheel well and then reached over the fender to tighten the bolt with a 10 mm socket. Getting my torque wrench on the bolts was a challenge (upper strut brace gets in the way) but hopefully I got the torques OK. I will re-check after 100 miles as they suggest. Next on the list is the rear sway bar, then I plan on installing the upper strut brace and the 6 point sub frame brace. I plan on doing each upgrade one at a time and will report back the results. As far as this one goes - it's a no brainer. Everyone with this car needs to install this. In my opinion, it should be viewed as a safety feature (of course, it also increases the fun factor too!) It's hard to believe Saab let this model out of the factory without this.

Rating: 5 of 5 Stars! [5 of 5 Stars!]

Write Review Back
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
5 x Shifter Mount Kit Cobalt/ HHR
1 x Saab black Keychain
3 x AEM Wideband Gauge Kit
5 x Short Shifter HHR Cobalt F35 F40
2 x Header Flange 1/2in Blended Transition B2x4,B2x5
3 x Universal / Special Request
4 x Clear Little Fender Blinkers Factory Saab
1 x 20th Viggen logo Shifter Top
1 x 9-3 / 900 Uprated Suspension Bushings Inner
1 x 9-3 / 900 Uprated Front ARB Bushings
1 x ATF Saab 3309 (Automatic 02->)
2 x PPC 3 Volvo Diagnostic System
3 x BBS Center Cap for 9-2x RK small caps
4 x Shift Rod Bushings
3 x Downpipe Flange Assy. Stainless T25/Td04 to 3in
1 x Oil Cap GM "HHR"
2 x Intake Flange B2x4 T5
1 x Head Bolt Washers
2 x Weld Bungs -Taper- Race Only
2 x T5 3.0 Bar Map Sensor Adaptor
1 x Injectors Green Giant 42lb (set 4)
3 x Crush Sleeve F35 F25
1 x Fuel Pressure Regulator 4.0 bar
1 x Quaife Differential 9-5 and Viggen (F35)
2 x Antenna Plug NG900/9-3 hatchback
2 x Rear Engine Mount 4cyl
2 x Fog light 9-3 left 99-00
1 x 9-5 Wheel 10-Spoke 16in.
2 x Turbo Conversion Pipe 900 9-3 T5
1 x MTF0063 Manual Gear oil
2 x Sport Transmission Mount 9-3/900 (Automatic)
1 x Basic Subframe Brace
2 x Moog Ball Joint
2 x Mat Set Textile Parchment 9-5 10-
2 x Midpipe 2.0T 07-11 FWD (2wd)
2 x Mat Set Black Rubber 9-5 10-
1 x Mat Set Textile Shark Grey 9-5 10-
3 x BSR 9-5 2010-2011 V6 300Hp
2 x Oil Cap 9-3SS V6 "Ghost"
2 x Storage Tray / Ashtray Kit 9-5 10-
2 x Mat Set Textile Jet Black 9-5 10-
2 x Oil Cap 9-3SS V6 "Griffin"
2 x ARP Exhaust Manifold Stud kit Stainless
1 x BSR Optiflow Intake 4cyl
1 x Hawk HPS FRONT Pads 9-3 9-5 (900 97-98)
1 x Rear Camber Shims Kit 6pcs
1 x Exhaust manifold Stud Kit
1 x Forge Bypass Valve Cobalt/HHR TC
1 x Catback 2.5in Exh 900/9-3 94-02 Round Tip
1 x Open Air Intake 9-3 00-02 and Viggen (All T7)
1 x 9-3 ng900 Hood Protection Strip
1 x 9-3 /NG900 Grille
1 x Shifter Alignment Pins (Set 2)
2 x Viggen Clutch Kit 99-02
1 x ARP Ring Gear Bolts F25/F35
1 x Open Air Intake 9000 93-98
1 x 9000 Shifter Bushing Repair Kit
1 x Cat Back Exh for 9000 CS, CSE AERO
1 x 9000 High Performance Brake Line Kit '95-'98
1 x 9000 Intercooler ETS
1 x Injectors Siemens 60lb 630cc (set 4)
1 x 3pt Subframe Brace for 9-3 SS 2003-> 2wd
1 x Fog light Replacement Panels
1 x v6 2.8t SAI Delete Kit
1 x BSR Optiflow Intake Volvo S60 I T5 2001-2004
1 x K&N Filter Service Kit
1 x Flywheel Twin Disk 7.25in B2xx
1 x Shifter Top Ghost Logo
1 x Slave Cyl
1 x Map/MAT sensor weld bung
$17,377.80
Manufacturer Info
Taliaferro
Other products
Share Product
Share via E-Mail